Guide

Flat Yarn Extrusion Line Specification: Output, Denier and Power

The fourteen fields a PP tape line quotation must fill, with Yanfeng Group's own catalogue figures: output in kg/h, die width, denier, draw ratio, winder speed, installed power and floor length.

A flat yarn extrusion line specification is a list of about fourteen numbers, and a quotation that fills all fourteen can be compared with any other quotation that does the same. Most cannot, because the fields that decide plant capacity — maximum output in kg/h, die width, denier range, draw ratio, winder speed and installed power — are the fields most often replaced by a line speed and a photograph. This page sets out the fourteen fields, says what each one commits you to, and answers each with Yanfeng Group's own catalogue figures. Yanfeng Group Co., Ltd. has built plastic weaving machinery in Pingyang, Wenzhou, Zhejiang since 1987, and every figure below comes from our product pages and our printed catalogue tables. For a ranked comparison of the machines themselves rather than the parameters, start from our flat yarn extrusion line round-up.

Key definitions

  • Flat yarn (PP tape): the flat, drawn polypropylene strip that a circular loom weaves into sack fabric. Everything upstream of the loom exists to make it.
  • Maximum extrusion output: kilograms of tape per hour at the die, the figure that sets plant capacity. Quoted as a range on the tape drawing machines and as a single maximum on the high-speed lines.
  • Die width / die lip width: the width of the molten film leaving the die, which fixes how many tapes the line can slit at a given tape width.
  • L/D ratio: screw length divided by screw diameter — a measure of how much melting and mixing the extruder does. Ours are tabled at 23:1 and 26:1 on the tape drawing machines and 33:1 and 30:1 on the high-speed lines.
  • Draw ratio (drawing ratio): how many times the film is stretched in the oven. It converts film thickness into tape strength and denier.
  • Denier scope (tex): the mass per unit length of the finished tape. Our high-speed line catalogue tables give 60–130 tex.
  • Installed power vs normal consumption: the connected load the switchboard must carry, and the load the line actually draws in steady running. They are different numbers and only the first sizes your supply.

The two high-speed line families, side by side

This is the clearest thing in our own data, and almost nobody asks about it. The 280 m/min YF-SPL line and the 450 m/min YF-GSPL line are tabled with identical die-lip widths, identical installed power, identical winding-spindle counts, identical footprints and identical weights. Four of the five frames carry the same screw diameter. Two columns differ.

Frame Screw dia. L/D Die lip Max output, YF-SPL (280 m/min) Max output, YF-GSPL (450 m/min) Spindles Installed power Normal consumption Installing dimensions (L×W×H) Weight
80 80 mm 33:1 800 mm 220 kg/h 320 kg/h 136 240 kW 120 kW 29000×3600×3200 mm 21,000 kg
90 / 100 90 mm (SPL) / 100 mm (GSPL) 33:1 1000 mm 280 kg/h 400 kg/h 176 290 kW 160 kW 32000×3600×3200 mm 26,000 kg
110 110 mm 30:1 1200 mm 350 kg/h 480 kg/h 208 320 kW 170 kW 34000×3800×3200 mm 30,000 kg
120 120 mm 30:1 1500 mm 450 kg/h 600 kg/h 256 380 kW 210 kW 37000×3800×3200 mm 32,000 kg
135 135 mm 30:1 2000 mm 550 kg/h 800 kg/h 344 450 kW 250 kW 45000×3800×3200 mm 40,000 kg

Both families are tabled at 20–120 r/min screw speed (20–100 on the 135 frame), 60–130 tex denier, a drawing ratio of 4–10 and a 38×230 mm bobbin, and both are listed CE in the catalogue. So the question "which line?" is not a question about width or power at all: at a given die lip and a given connected load, you are choosing how many kilograms per hour you want out of it. The catalogue adds that the number of spindles can be collocated to the customer's requirements and that bobbin specifications can be made to order, so the spindle column is a starting point rather than a fixed property.

The lines are specified for PP, HDPE and LLDPE flat yarn, use computer-controlled frequency-conversion speed regulation, and can be ordered with a filter-change structure and a fibrillation structure for flexible packaging bags or fibrillated sewing thread. Heating of the stock thread is either a hot-blast stretching oven or an electric baking board — a choice made at order, not afterwards. Both pages carry the full tables: the 450 m/min line and the 280 m/min line.

Where the SJ-FS tape drawing machine fits

The Plastic Tape Drawing Machine is the other half of the tape line range and it answers a different question: width and feedstock flexibility rather than speed. Its catalogue table runs to sixteen sizes, from SJ-FS110/800B to SJ-FS230/5800B — screw diameters 110 to 230 mm, screw lengths 2,500 to 7,500 mm, die widths 800 to 5,800 mm, extruder motors 30 to 185 kW, extruder heating 36 to 165 kW, traction 7.5 to 37 kW, heating-board power 15 to 70 kW, a 5.5 kW vacuum pump on the (P) sizes, production capacity 60 to 700 kg/h, linear speed 80–200 m/min, installing lengths 13.3 to 25 m and weights 6,500 to 45,000 kg. The product table adds an L/D ratio of 23:1 on the 110 and 120 mm screws and 26:1 on the larger ones, screw speeds falling from 25–75 r/min to 20–60 r/min as the screw grows, a drawing rate of 4–8 and a tape thickness of 0.025–0.08 mm narrowing to 0.025–0.06 mm on the widest dies.

Three practical points from that table that a quotation should state and usually does not. The catalogue says the machine can take 100% recycled materials, high-rate master batch, mixed materials, powder or granules, with a 38CrMoAlA alloy-steel screw and barrel. It says an active roller is used when die width is over 2 m, and a separate note warns that the installing width is 400 mm wider on the active-roller version — a layout difference that arrives after the drawing is approved if nobody asked. And the drawing ratio is changed either by a six-speed gearbox or by a servo numerical-control system, which is a different machine to operate and a different spare-parts list.

One more column deserves attention because it is the one buyers skip: the table prints the reducer model for each size — ZLYJ315 on the 140 and 150 frames, ZLYJ330 on the 160s, ZLYJ375 on the 170s, ZLYJ420 on the 200s and ZLYJ450 on the 230. An extruder drive is a long-life, high-torque item and the model number is the only way to price a spare or a replacement later. Require it in writing.

The fourteen fields, with two worked examples

Make every supplier fill the same fourteen fields for a specific model, then compare the filled forms rather than the sales language. These are the fields our own tables already print, with one tape drawing machine and one high-speed line as worked examples at opposite ends of the range.

Field SJ-FS140/2000B(P) tape drawing machine YF-GSPL-120/30/1500 high-speed line
Maximum output 150–300 kg/h 600 kg/h
Screw diameter 140 mm 120 mm
Screw length / L/D ratio 4,800 mm 30:1
Screw rotational speed 20–60 r/min (product table, 140 frame) 20–120 r/min
Die width / die lip 2,000 mm 1,500 mm
Maximum linear speed 80–200 m/min (catalogue table) 450 m/min
Denier scope — (tabled by tape thickness, 0.025–0.06 mm) 60–130 tex
Draw ratio 4–8 4–10
Winding section separate winder, see below 256 spindles, bobbin 38×230 mm
Extruder motor power 45 kW — (system figure only)
Heating power 86 kW extruder + 30 kW heating board — (system figure only)
Installed power / normal consumption 45 + 86 + 30 + 7.5 kW traction + 5.5 kW vacuum pump, itemised 380 kW installed / 210 kW normal
Installing dimensions (L×W×H) 20800×3400×2200 mm (+400 mm width with active roller) 37000×3800×3200 mm
Weight 20,000 kg 32,000 kg
Reducer model ZLYJ315 — (not tabled)
CE in catalogue yes yes

Two things to notice, because they are the two that cost money later. The power figure comes in two forms and they are not interchangeable: the drawing machine's catalogue itemises extruder motor, extruder heating, traction, heating board and vacuum pump separately, while the high-speed line gives one installed figure and one normal-consumption figure. Add the itemised columns yourself before you size a transformer, and never size it on the normal-consumption number. And the floor length is the parameter that most often kills a layout: 13.3 to 25 m for a drawing machine against 29 to 45 m for a high-speed line, before any allowance for the winder, material handling or walkways.

Check the winder against the line, not against the brochure

The winding section is specified in its own table, and this is the mismatch we see most often in enquiries. Our winding machine range lists two families. The cam-type S-STL-II winders — our own design, with a cardioid cam in place of the older reciprocating-shaft mechanism and five winding layers on both sides to shorten the machine (patent ZL03203782.1) — are tabled at 80–150 m/min tape-winding linear speed, with ten catalogue sizes from 190 to 760 spindles, main motors of 1.5–2.2 kW and winding motors of 9–33 kW, and they are listed CE. The inverter-control and single-spindle magnetic S-SDC winders are tabled at 80–280 m/min, with 136, 176 and 208 spindles and gross motors of 25, 31 and 38 kW, and they are not listed CE in the catalogue. Every winder in both families takes the same 38×230 mm bobbin as the high-speed lines.

So the rule is simple and checkable: read the winder's tape-winding linear speed and the line's maximum linear speed off their two tables and confirm the first covers the second. The 450 m/min line is specified with its own 136–344-spindle winding section for exactly this reason. If an offer pairs a high line speed with a separately-quoted winder whose own table stops lower, that is a question to ask before signing, not a detail. The selection logic for the winders themselves is set out in our winding machine comparison.

Our recommendation

Do not start from a line speed, a screw diameter or a model number. Start from five numbers — finished fabric width, fabric weight in g/m², tape denier or thickness, daily output in tonnes or in bags, and the feedstock you will actually run (virgin granules, recycled granules, powder or a master-batch blend) — and ask two or three suppliers to return the fourteen fields above for one specific model. A supplier who answers with a line speed and no kg/h has not sized anything. A supplier who gives one power figure without saying whether it is installed or consumed has given you the smaller of the two. A supplier who will not print the die width against your fabric width has not matched the line to your loom. All three are knowable before the order.

Send those five numbers, or simply describe the sack and the output you need, through the enquiry form. Our International Trade Department returns a model, the fourteen fields filled in and a layout drawing. Where the tape line sits in the whole plant — extrusion, weaving, lamination, printing, cutting and sewing — is set out in our PP woven bag machine production line guide, the looms that consume the yarn are compared in our circular loom buyer's guide, and the workshops and machine tools behind these lines are listed on our production capacity page. Office hours are Monday to Saturday 08:00–17:30 and Sunday 09:00–17:30, China Standard Time (UTC+8).

What our published data does not give, and what we will not invent to fill a quotation: prices, lead times, delivery or payment terms, warranty periods, output or uptime guarantees, energy consumption per kilogram of tape, bags-per-shift conversions, or a maximum linear speed for the 280 m/min line while our own two tables disagree about it.

Frequently asked questions

Which single number decides a flat yarn extrusion line's size?
Maximum extrusion output in kg/h, not line speed. Our catalogue tables run from 60–120 kg/h on the smallest SJ-FS110/800B tape drawing machine to 500–700 kg/h on the SJ-FS230/5800B, and from 320 kg/h to 800 kg/h across the five frames of the 450 m/min YF-GSPL line. Fix the kg/h you need for the fabric weight and the daily output you are planning, then read the die width and installed power off the same row. A quotation that leads with line speed and omits kg/h has told you nothing about capacity.
What does 'high speed' actually buy on a tape line?
Output from the same machine. Our 280 m/min YF-SPL line and our 450 m/min YF-GSPL line are tabled with the same five die-lip widths, the same installed power, the same number of winding spindles, the same footprint and the same weight — four of the five frames even carry the same screw diameter. The only columns that differ are maximum output and maximum linear speed: 220, 280, 350, 450 and 550 kg/h on the SPL against 320, 400, 480, 600 and 800 kg/h on the GSPL. The high-speed line produces more kilograms per hour from the same connected load and the same floor area.
How do I know the winder can keep up with the line?
Compare the winder's listed tape-winding linear speed against the line's maximum linear speed, because they are two separate figures in two separate tables. Our cam-type S-STL-II winders are listed at 80–150 m/min and our magnetic and inverter-control S-SDC winders at 80–280 m/min, while the 450 m/min line table specifies its own winding section of 136 to 344 spindles. If a quotation pairs a line speed with a winder whose catalogue winding speed is lower, ask which of the two figures the plant will actually run at and get the answer in writing.
Can the line run 100% recycled material?
The SJ-FS tape drawing machine can, according to its catalogue: 100% recycled materials, high-rate master batch, mixed materials, powder or granules. The screw and barrel are 38CrMoAlA alloy steel. The high-speed YF-SPL and YF-GSPL lines are specified in the catalogue for PP, HDPE and LLDPE flat yarn. If recycled feedstock is your plan, say so in the enquiry, because it changes which family is the right starting point.
Where do our own published figures disagree, and what should I do about it?
In three places, and they are worth knowing because the same traps appear in other suppliers' documents. The SJ-FS product table prints a linear speed of 50–150 m/min where the catalogue table prints 80–200 m/min, and a production capacity of 50–220 kg/h where the catalogue prints 60–700 kg/h across more sizes; the catalogue table is the one we stand behind in both cases. And the catalogue table headed '280 m/min Extrusion Line' prints 450 m/min in its maximum-linear-speed column for every row, while the product page for the same line states 280 m/min. We will not guess at that one: ask for the maximum linear speed in writing against your model number.
Plastic Weaving Machinery · International Trade Department

Talk to our export team

Send us your bag size, output target and raw material and we will propose a complete line, or ask for a price and delivery time for a single machine. We answer in English; Arabic-speaking agents are available on request.