Guide

Gear Reducer Model Number: How to Read a Type Designation

A gear reducer model number is a type designation of eight to eleven fields. What each field commits you to across our nine series, why the number in the middle means a different thing in each family, and which fields quotations leave out.

A gear reducer model number is not a part number; it is a type designation, a string of eight to eleven fields in which every field is a decision that was taken when the unit was ordered. Read the string and you know the series, the mounting, the size, the ratio, which way the output shaft points and which way the input is allowed to turn. Miss a field and the factory picks it for you. This page is the cross-series reader: what each field commits you to, why the digits in the middle mean a different thing in each of our families, and which fields a quotation most often leaves out. It is deliberately not a sizing guide — the torque, power and thermal calculations live in the series guides linked throughout, starting with our gear reducer selection guide.

Key definitions

  • Type designation (model number): the ordered string of fields that identifies one configuration of one series. Our catalogues print it as the "type designation" or "model and marking" key.
  • Enterprise code: the leading YF on our units.
  • Series letter(s): R, F, K, S, P, H, B, ZDY/DBY family codes, T, SWL.
  • Mounting structure: the code for feet, flange, hollow shaft or a combination of them — a different code set in each series.
  • Frame size: the catalogue size index. In most families it is an index with no physical unit; in two of ours it is a real measurement.
  • Nominal ratio: the ratio the catalogue table offers, which is rarely exactly the ratio you calculated.
  • Mounting position: the orientation the unit is built for. It sets the oil fill and the position of the breather, oil sight glass and drain plug.
  • Assembly pattern / assembly design: the arrangement of shafts and faces within one frame, a separate field from the mounting position.
  • Input rotation: the direction the input shaft is allowed, or expected, to turn — S/N or CW/CCW depending on the series.

The nine patterns side by side

Every series catalogue prints its own worked example. Here they are together, as printed, with what the leading fields do:

Series Example as printed in the catalogue Fields in the string
R, F, K, S geared motors YF K A 67 B Y -4 -4p i9.66 M1 B 180 2 enterprise code, series letter, mounting structure, frame size, motor power and poles, ratio or output speed, mounting position M1–M6, output-shaft side, terminal-box position, additions
P planetary YFP2 S AZ -12 -80 -B512 -96 -CW series and stage count, input structure, output-shaft design, size, nominal ratio, mounting position, add-on piece, input rotation
H/B industrial YFB 2 S H -10 -12.5 -A -CW series type, number of stages, output-shaft design, mounting, size, nominal ratio, assembly design, input rotation
ZDY/DBY national-standard YFD B Y K 160 14 III S type, stage code, hardened tooth, output shaft, final-stage centre height, nominal ratio, assembly pattern, input rotation
T spiral bevel YF T 12 2:1 D-LR B3 series, size, ratio, shaft arrangement, mounting position
SWL screw jack YFSWL 2.5 M 1 A 500 Z I series, size, worm ratio, structural type, assembly form, travel in mm, accessory, screw-end coupling

Two things follow immediately. The strings are not the same length and not in the same order, so a column of model numbers from a multi-series quotation cannot be read down the page. And four of the six carry an input-rotation field, which is the field buyers most often discover after delivery.

The number means a different thing in each family

This is the part worth printing out. Across our range the digits in a model number carry four unrelated meanings:

Family The digits are Range printed in the catalogue So 160 would mean
R, F, K, S frame size — an index, no unit R17–R167, F37–F157, K37–K187, S37–S97 nothing: there is no frame 160 in these series
P size, then the nominal ratio sizes 9–36 nothing: outside the size range
H/B stage count first, then the size stages 1–4, sizes 1–22 nothing: outside the size range
ZDY / DBY final-stage centre height, in millimetres ZDY 80–560, ZLY 112–710 a 160 mm centre height
T frame size — an index, no unit T2–T25 nothing: outside the size range
SWL rated lifting force, in tonnes 1–100 t a 160-tonne jack, which we do not make

So YFSWL25 is a 25-tonne jack, ZLY250 is a unit with a 250 mm final-stage centre height, and K157 is the tenth of twelve K frames and not 157 of anything. A number without its series letter is not a size. Two of our own families cannot be compared digit for digit even when the digits match, which is the whole reason this page exists: an enquiry quoting "a 160" is ambiguous, and so is a comparison between two offers in which only one side named its series.

The same letter, three different jobs

Letters are reused across the series keys, and the overlaps are not harmless:

Letter In the geared-motor series (R/F/K/S) In the P series In H/B In ZDY/DBY, T, SWL
S the helical-worm series an added helical input stage solid output shaft S = clockwise input rotation on ZDY/DBY
K the helical-bevel series a bevel-helical input stage — hollow shaft on ZDY/DBY (KD with shrink disc)
A hollow shaft mounting (AF with B5 flange, AZ with B14, A…B with feet) part of AZ/AH hollow-shaft codes assembly design A SWL assembly form A, screw travels upward
F B5 flange mounting (…F feet plus flange) — — SWL accessory F, anti-rotation device
D — — hollow shaft with shrink disk T shaft arrangement D-…, downward shaft

Read every letter against the key of its own series catalogue. And note one more trap inside a single family: in the R series the bare YFR is the foot-mounted unit and YFRF the B5 flange version, while the F series key lists YFF as the flange version with the foot-mounted code omitted. The absence of a letter is itself a field, and it does not mean the same thing in both keys. Name the mounting in words as well as in code.

Decoding the geared-motor string

The geared-motor key is the longest in our range and the one most often quoted incompletely. Taking the catalogue's own example, YF K A 67 B Y -4 -4p i9.66 M1 B 180 2:

Field In the example What it fixes
Enterprise code YF our units
Series letter K right-angle helical-bevel; R coaxial, F parallel-shaft, S helical-worm
Mounting structure A hollow output shaft; see the letter table above
Frame size 67 one of K37–K187 here
Motor power and poles -4p the pole count, 4-pole in the catalogue's example, alongside the motor power where the unit is supplied as a geared motor
Ratio or output speed i9.66 the ratio, or the output speed — the key allows either, and they are not the same order
Mounting position M1 one of M1–M6
Output-shaft side B A, B or A+B for a double-ended shaft
Terminal-box position 180 0°, 90°, 180° or 270°
Additions 2 further options from the key

The printed example carries two single letters in the middle, and because our published data names the field order without pinning each letter in that example to a position, the authority for which letter is which is the type-designation key in the series catalogue on each series page — not this page and not a supplier's e-mail. That is not a weakness of the string; it is the reason to ask for the key alongside it. Whether the motor belongs in the string at all is a separate decision, set out in our geared motor guide.

Four fields our catalogues single out

  1. The K series bears load in one direction only. The selection guide states it plainly: for YFK spiral-bevel units the rotating direction, viewed from the output shaft, should be indicated when ordering, because it improves the pressing state of the spiral bevel gears. This is not a preference field. The T series by contrast is suitable for forward and reverse rotation.
  2. Input rotation is a field in four families. S clockwise or N counter-clockwise on ZDY/DBY, CW or CCW on H/B and P. If the string you were sent has no rotation field, the order is incomplete.
  3. The assembly pattern is not the mounting position. ZDY/DBY carries assembly patterns I to IV from its pattern table and H/B carries assembly designs A to D, each in addition to the mounting field. Two units in the same frame and the same mounting position can be different machines.
  4. On the T series, which shaft you drive changes what the box does. For any ratio other than 1:1 the catalogue asks you to state the input shaft: driving the horizontal shaft reduces speed and driving the vertical shaft increases it. Once the mounting orientation and dimensions are set, the shaft positions cannot be changed.

Across every series, the mounting position also sets the lubrication detail — the oil quantity and the positions of the breather, oil sight glass and drain plug are defined per position and built in at the factory. The quantities themselves are in our maintenance guide.

What to insist on in writing

  1. The complete type designation, every field filled, not an abbreviation.
  2. The series catalogue's field key next to it, so the positions are not in dispute. Each series PDF is on its series page under gear reducers.
  3. The rated figure that belongs to that series: permissible output torque for R/F/K/S, output torque for P and H/B, nominal input power and the thermal capacity for ZDY/DBY, rated output torque for T, permissible load for SWL. The nine series are compared side by side in our industrial gear reducer round-up.
  4. The nominal ratio actually on offer and the output speed it gives, stated separately, because the geared-motor key accepts either in that field.
  5. The mounting position, output-shaft side, terminal-box orientation and input rotation, in words as well as in code.

Our recommendation is narrow and practical: treat the designation as the contract and the rated figure as the specification, and refuse to compare two offers until both are complete. If you are holding a nameplate rather than a quotation, send a photograph of it — because the frame sizes and ratios follow the industry-standard designation, an existing R, F, K or S unit can usually be matched in the same frame size and ratio.

What our published data does not give, and we will not invent. It does not give the position of every letter in every printed example — the series key does. It gives no torque, ratio or power figure in this page's scope, because notation is not sizing and the series guides own those tables: the R/F/K/S method for the f1/f2/f3 service factors, the worm-gear S series and SWL screw jack guides for their own selection steps. And it gives no oil grades, viscosities, fill volumes, efficiency percentages, unit weights, prices, lead times or delivery terms. Nor can we tell you what another manufacturer's designation means; only ours.

Send the duty, the layout and — if you have one — the designation or nameplate photograph through the enquiry form. Our Reducer Sales department and engineers return a complete type designation, the rated figure against it and a dimension drawing. Yanfeng Group Co., Ltd. has designed and built gear reducers and plastic weaving machinery in Pingyang, Wenzhou since 1987, across the R, F, K, S, P, H/B, ZDY/DBY, T and SWL series, and can take orders for products of special specification with an exclusive design service. Office hours are Monday to Saturday 08:00–17:30 and Sunday 09:00–17:30, China Standard Time (UTC+8).

Frequently asked questions

What is a gear reducer model number made of?
It is a type designation: a string of eight to eleven fields, each of which is a decision taken at order. Across our range the fields are the enterprise code YF, the series letter, the mounting structure, the frame size, the motor power and pole count where a motor is included, the ratio or output speed, the mounting position, the output-shaft side and the terminal-box orientation, plus series-specific fields such as the assembly pattern and the input rotation. A string with a field missing is not a smaller order; it is an order someone else will complete for you.
Does the number in a reducer model number mean the same thing in every series?
No, and this is the single most common mistake made when comparing two quotations. In the R, F, K, S and T series the number is a frame size, an index with no physical unit. In the ZDY/DBY series it is the final-stage centre height in millimetres. In the SWL screw-jack series it is the rated lifting force in tonnes, so YFSWL25 is a 25-tonne jack. In the H/B series the first digit after the series letters is the number of gear stages and the size comes later. Four families, four different meanings for the digits, so the digits can only be read after the series is known.
Why does the same letter mean different things in different series?
Because each series catalogue has its own type-designation key and the letters are reused. S is the helical-worm series letter in the geared-motor range, an added helical input stage in the P series and a solid output shaft in the H/B series. K is the helical-bevel series letter, a bevel-helical input stage in the P series and a hollow shaft in the ZDY/DBY series. A and F are mounting structures in the geared-motor range and an assembly form and an anti-rotation accessory in the SWL series. Read every letter against the key of the series it belongs to, and never carry a letter's meaning from one family to another.
Which fields do enquiries most often leave out?
Five, in our experience of returning selections. The mounting position, because it sets the oil fill and the position of the breather, oil sight glass and drain plug and is fixed at the factory. The input rotation, which the K series needs because its spiral-bevel gears bear load in one direction only and the ZDY/DBY, H/B and P series carry as an S/N or CW/CCW field. The output-shaft side, A, B or A+B. Whether the ratio quoted is the nominal catalogue ratio or the output speed you actually need, which are not the same order. And on the T series, which shaft is driven, because that decides whether the box reduces or increases speed.
How do I check that a quotation is for the unit I asked for?
Ask for the complete type designation together with the field-by-field key from the series catalogue, and ask for the rated figure that goes with it: permissible output torque for the geared-motor series, output torque for P and H/B, nominal input power and thermal capacity for ZDY/DBY, rated output torque for T, permissible load for SWL. A designation on its own identifies a configuration, not a capacity. A capacity on its own does not identify a unit you can install. A supplier who can return both, and name the field positions, has done the selection.
Plastic Weaving Machinery · International Trade Department

Talk to our export team

Send us your bag size, output target and raw material and we will propose a complete line, or ask for a price and delivery time for a single machine. We answer in English; Arabic-speaking agents are available on request.